Panasonic FZ-1 sollutions for most Common Technical Faults

Got a problem with your 3DO? Ask!
oldskool
3DO ZERO USER
Posts: 228
Joined: Tue Feb 09, 2010 6:45 pm
Location: Las Vegas

Post by oldskool » Tue Apr 20, 2010 9:05 am

Oh ok, well it must be a common problem then, because another guy is having the exact same problem that you are having, and on an FZ-10 even. And people seem to think the FZ-10 is more reliable.. :roll:

Good luck. :wink:
Image

knight2000
3DO ZERO USER
Posts: 3
Joined: Thu Aug 19, 2010 7:13 pm
Location: PA USA
Contact:

Post by knight2000 » Sun Aug 29, 2010 2:55 am

Is there an english guide for the laser swap yet? For the new sf-92.5? The russian guide is a little tough to follow.

Thanks in advance :D

acem77
3DO ZERO USER
Posts: 107
Joined: Fri Aug 03, 2007 1:39 am
Location: Ohio

Post by acem77 » Mon Sep 27, 2010 9:57 pm

so is there one final best solution to replace the laser in a fz1?
my RGB 3dos laser is 98% dead now.

just got it to boot it 1 more time to start Taiketsu! Rooms for the my 1st time to play this great multi player game.
great game more on that later..

it wont boot anything most of the time now.... :cry:


update i dont think its my laser, its the drive shaft.
the plastic gear at the end is split making it a little wider on the split half.

as the drive spins it will get hung up at that revolution.
i tried to loosen the braket that hold the motor then its does not grip the gear good enough, too tight and it locks the drive shaft per the revolution.

its time to replace it.

anyone have a dead fz1 cd drive. i dont need a working laser.
let me know ill buy it from you .

Image

acem77
3DO ZERO USER
Posts: 107
Joined: Fri Aug 03, 2007 1:39 am
Location: Ohio

Post by acem77 » Wed Oct 06, 2010 6:06 pm

Fixed! :)

with a gear from a Sony CDU-8002 mechanism inside an AppleCD-150.
A guy at a local pc store gave me some old cd roms from 1992-1997.

http://www.performance-gear.com/images/proto.JPG
the gear looked like the lower gear in the above pic.
i removed the center part and cut that in half so i got 2 replacement gears out of it.
I then used a small screw driver to gouge the hole in a few spots.
now the shaft fits snug with no glue.

The 3do is working great

Aaron
3DO ZERO USER
Posts: 2
Joined: Thu Oct 07, 2010 6:57 am

Post by Aaron » Thu Oct 07, 2010 7:00 am

Thanks for posting the info acem77. I have been trying to find a new gear for the FZ-1 I got a few weeks ago. My gear split in the exact same spot. Its like it shrunk over time or something.

Aaron
3DO ZERO USER
Posts: 2
Joined: Thu Oct 07, 2010 6:57 am

Post by Aaron » Fri Oct 08, 2010 4:04 am

Oh,by the way, how did you cut the new gear?

acem77
3DO ZERO USER
Posts: 107
Joined: Fri Aug 03, 2007 1:39 am
Location: Ohio

Post by acem77 » Fri Oct 08, 2010 5:44 pm

I used a grinding wheel to remove the thin large diameter gear.
Then a dermal in a vice with a thin cut off wheel to cut the center piece in half.

Rust
3DO ZERO USER
Posts: 33
Joined: Wed Nov 17, 2010 11:45 pm

Post by Rust » Wed Nov 17, 2010 11:59 pm

Hm, I'm glad I ran across this forum. My FZ-1 has been gathering dust in my closet for ages because the power won't come on. The fuse at TM1/TM2 blew out, and upon replacement it just blew out again instantly. Because of the physical location I suspect some sort of power supply issue, but I'm more of a MacGyver than a Nikolai Tesla, so I'm hesitant to delve too far into the circuitry without a little guidance. Could anyone provide any insights or a solution?

Shane#
SPAMMER
Posts: 1
Joined: Sat Apr 02, 2011 2:33 am

Post by Shane# » Sat Apr 02, 2011 2:39 am

is this easy enough to do? i have a good working 3do, but i would like to pickup a replacement laser and motors for furture breakdowns! does anyone know if there are any cd players or devices that normally have these lasers in them? im a frequent vistors to the many thrift stores around here, tons of cd players around! found one a while back with the proper laser and motor for sega cd replacement!

luthors
SPAMMER
Posts: 1
Joined: Wed May 11, 2011 11:46 pm

Post by luthors » Wed May 11, 2011 11:52 pm

supongo que es este el lente que buscan
http://www.cm2.cl/busqueda.php?b=SF-92.5&btn=Buscar

jessfriends
SPAMMER
Posts: 1
Joined: Wed Jun 29, 2011 3:53 am

Post by jessfriends » Wed Jun 29, 2011 6:37 pm

Any updates on this? I just got an FZ-1 model from an estate sale and since it powered on i thought it would work, but it won't read games. The games are not spinning so I thought it was the motor but now i am not sure if they laser is working. Should I see a light coming from the laser? Also maybe the white gear is broken?

I took it apart last night and will look at it again tonight to see if the white gear is in good shape.

I think I need a new motor and/or laser. Where can I get these at or what exactly am I looking for? I would like to attempt to fix this thing.

I can try to post pictures later.

If anyone has any info or help for me I would appreciate it!

Thanks.[/img]

jetblue
3DO ZERO USER
Posts: 3
Joined: Sun Jun 22, 2008 6:42 am

Post by jetblue » Mon Jun 03, 2013 5:46 am

hi,i forgot i was a member here. if i knew i would have done my repair thread here. heres a link to how i fixed my broken gear 3do.

http://nfggames.com/forum2/index.php?topic=5105.0


hope this helps.

Post Reply